英文字典中文字典


英文字典中文字典51ZiDian.com



中文字典辞典   英文字典 a   b   c   d   e   f   g   h   i   j   k   l   m   n   o   p   q   r   s   t   u   v   w   x   y   z       







请输入英文单字，中文词皆可：

protrusion    
n. 推出,突出,露出

推出,突出,露出

protrusion
n 1: something that bulges out or is protuberant or projects
from its surroundings; "the gun in his pocket made an
obvious bulge"; "the hump of a camel"; "he stood on the
rocky prominence"; "the occipital protuberance was well
developed"; "the bony excrescence between its horns" [synonym:
{bulge}, {bump}, {hump}, {swelling}, {gibbosity},
{gibbousness}, {jut}, {prominence}, {protuberance},
{protrusion}, {extrusion}, {excrescence}]
2: the act of projecting out from something [synonym: {protrusion},
{projection}, {jut}, {jutting}]

Protrusion \Pro*tru"sion\, n.
1. The act of protruding or thrusting forward, or beyond the
usual limit.
[1913 Webster]

2. The state of being protruded, or thrust forward.
[1913 Webster]


请选择你想看的字典辞典：
单词字典翻译
Protrusion查看　Protrusion　在百度字典中的解释百度英翻中〔查看〕
Protrusion查看　Protrusion　在Google字典中的解释Google英翻中〔查看〕
Protrusion查看　Protrusion　在Yahoo字典中的解释Yahoo英翻中〔查看〕

安装中文字典英文字典查询工具!


中文字典英文字典工具:
选择颜色:
输入中英文单字

































































英文字典中文字典相关资料:


  • Protrusion, CR | Cummins Diesel Forum
    The piston protrusion specs I have and what you have posted are for 94 and later emissions controlled automotive apps, these engines have compression ratios ranging from 17 1:1 up to 17 5:1 My Cummins maintenance manual list industrial off road engines with compression ratios from 16 5:1 up to 18:1
  • Piston protrusion | Cummins Diesel Forum
    Hey I just finished installing my pistons and was going through to check the protrusion and number 1 was in aspect 25 thousands but the rest where all at 35 thousands Im not sure what to do about this should I run the 10 thousands over head gasket or try to fix it The block was cleaned up at
  • Piston protrusion specs,,,Im so confused | Cummins Diesel Forum
    I'm in the process of putting together a 12 valve for a conversion project The block needed a 0 020 overbore and I waited for like four months for some Mahle motorsport performance cast pistons What I don't understand is how much piston protrusion is acceptable before a thicker head gasket is
  • Piston protrusion below specs | Cummins Diesel Forum
    I measured my piston protrusion on my 12v and my protrusion is way below specs I am at 016 and my other pistons are about the same and or slightly lower
  • Piston Protrusion Over Spec. What Head Gasket?
    The problem: I measured my piston protrusion over the wrist pin as the manual instructs and had a couple of pistons that are a bit out of spec coming in with a total protrusion of 0 022" The service manual says that min protrusion is 0 006" and max is 0 019" and if you are outside this range then you have a problem
  • piston protrusion and valve face depth for hamilton cam
    hey, I am in the process of building my p pumped 24 valve and just have gotten my shortblock and cylinder head back from the machine shop and I was measuring piston protrusion and valve face depth to determine if the Hamilton 188 220 would have proper clearance and it looks like I may have some
  • Piston protrusion question | Cummins Diesel Forum
    piston protrusion will determine what head gasket you use the information is in the factory service manual It was several years ago i rebuilt mine so i do not remember if the manual gave any min or max values, just if it is above x amount of protrusion use the thick gasket, and below use the thin gasket
  • Headgasket thickness PTV compression HELP | Cummins Diesel Forum
    For piston protrusion I have tried to find exact figures for my 97 I read one thread that posted 0 024-0 028 protrusion is oem spec Mine being 030- 034 if I went with a 010 over head gasket I'm assuming I would lose a little bit of compression across the board but also increase my PTV
  • Need Guidance - Head Gasket Thickness | Cummins Diesel Forum
    In the process of rebuilding a 2006 5 9 block with a 2005 head on it The block is not machined, pistons are standard size, and rods are 6 7 rods Piston protrusion is at 0 014 We have a 1 28 head gasket and trying to decide if we should run it With that head gasket, the clearance between the
  • BBi Injector protrusion? | Cummins Diesel Forum
    I just installed a couple BBi injectors with SAC nozzles and the injector protrusion is 018 shy of the minimum 096 called for in the cummins manual I understand these differ from the factory VCO nozzles Is this a normal protrusion with the change in nozzle design? Obviously the concern is





中文字典-英文字典  2005-2009